camshaft

Structural Character Design Manufacture of Shell Molding Camshaft Die

壳型铸造凸轮轴模具结构特点与设计制造

互联网摘选

The effection on timing driving system by construction of the admission gear has been studied in this paper. A new effective design calculation way of the engine timing belt drive struction has been developed through designing and studying double overhead camshaft timing driving struction of 469Q engine.

通过469Q汽油机双顶置凸轮轴正时传动机构的设计研究，开发了一种有效的发动机正时同步带传动机构的设计计算方法，对发动机正时传动机构的设计具有重要参考价值；

互联网摘选

This paper established a jet-pulse width alcohol, oil supply tension bar displacement, camshaft speed signals such as the model of relations.

由此本文建立起喷醇器脉冲宽度、供油拉杆位移量、凸轮轴转速等信号量的模型关系。

互联网摘选

This means that the crankshaft will make two revolutions for every revolution of the camshaft.

这意味着凸轮轴每旋转一次曲轴将旋转两次.

网络文摘精选

Since 1958, an engine with a single overhead camshaft has been used.

从1958年起, 便已使用带有单顶置凸轮机的发动机.

词典精选例句

Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.

网络文摘精选

The front timing cover and and a finished camshaft with timing gear on the end.

前面的时间和范围,并完成与凸轮轴齿轮的时间就结束.

网络文摘精选

This is called an overhead camshaft arrangement.

这被叫为顶置凸轮轴装置.

网络文摘精选

As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.

当凸轮轴旋转时, 凸轮凸起的或者高点的位置, 推动气门座.

网络文摘精选

The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.

曲轴的转速与凸轮轴的转速之比是2∶1.

网络文摘精选

Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面.

网络文摘精选

The result showed that the Rockwell hardness of the high pearlite-containing nodular iron camshaft increased with increasing of its nodularity and pearlite content.

结果表明，高珠光体含量球铁凸轮轴的洛氏硬度随着球化率和珠光体含量的升高而增加。

互联网摘选

The opening of each valve is controlled by a camshaft.

每个阀门的开启由凸轮轴控制.

网络文摘精选

The influence of inoculant addition amount on the structure and properties of camshaft was investigated.

试验了孕育剂量对凸轮轴组织和性能的影响.

网络文摘精选

A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.

推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.

网络文摘精选

The camshaft rotates in phase with the crankshaft, but at half its speed.

凸轮轴和曲轴协调旋转, 但速度仅是曲轴的一半.

《简明英汉词典》

The practical production has verified that the overmeasure of camshaft workpieces has been well distributed and met the working requirements when the cam masters designed in this way have been used.

经生产实践验证，用这种方法加工出的凸轮工件余量均匀，符合工艺要求。

互联网摘选

The isothermal quenching process of the ductile iron camshaft was analyzed.

对球铁凸轮轴的等温淬火工艺进行了分析.

网络文摘精选

In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.

网络文摘精选

Fit the short guide rails between the camshaft timing gears.

安装凸轮轴正时齿轮之间的短导轨。

provided by jukuu

The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.

那金属轴叫凸轮轴, 在发动机里的每个气门一般有各自的凸轮.

网络文摘精选

The camshaft has a cam, on which there is a lob , or bump.

凸轮轴上有一个凸轮, 凸轮上有一个凸角.

网络文摘精选

These engines are known as dual overhead camshaft ( DOHC ) engines.

这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.

网络文摘精选

The manganate phosphating technology of camshaft is introduced.

介绍凸轮轴的磷化工艺.

网络文摘精选

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.

网络文摘精选

Study on the Intelligent Grinding Parameter Selecting Model for A CNC Camshaft Grinding Machine

数控凸轮轴磨床磨削参数智能化选择模型研究

互联网摘选

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.

网络文摘精选

Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.

工件恒角速度磨削和工件恒线速度磨削是目前精加工凸轮轴的主要磨削加工工艺.

网络文摘精选

The camshaft and crankshaft gears can be connected directly, or meshed.

凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.

网络文摘精选

Argon arc remelting hardening is a new technology of manufacturing camshaft.

氩弧重熔硬化是生产凸轮轴新工艺.

网络文摘精选